Bench Press Pad Comparison: Launch Pad® vs Fat Pad vs ROM Pad vs ROM BloQ
Bench press pad comparison · Launch Pad®, Fat Pad, ROM Pad, ROM BloQ and the flat bench
What changes when you change the surface?
A wider pad, a narrow raised support and a contoured interface each create a different relationship between the athlete and the bench. To compare them meaningfully, look at where each one supports the body, how it behaves under load, what movement it allows, and what evidence stands behind its claims. Watch the demonstrations, compare the designs and review the documented results.
On this page
How to read this guide
Every statement on this page belongs to one of four kinds of evidence, and they are labeled so you can tell them apart.
A product fact from the manufacturer’s own page, or a dated public record.
What a manufacturer or a speaker says a product does.
What you can see for yourself in the footage.
What a defined study recorded, with its comparison condition named.
Manufacturer details reviewed November 18, 2026. “Not listed” means the reviewed page does not state it. Trademarks belong to their respective owners.
Watch the support differences
The clips below are short excerpts of real products on real benches. Each one names the product and who filmed it, and the notes separate what is visible from what the speaker explains, because a demonstration can show a setup clearly without proving what happens inside the shoulder.
AbMat ROM Pad: fit, stability and foam response
AbMat branding is visible on the pad and strap. Filmed by AMM with an AMM customer who bought this ROM Pad.
ShownStrap fit and adjustment on this bench. The strap is wrapped, pulled and repositioned while the participants talk through getting the fit they want. They say it has only one setting and that the pad pulled down out of position. Their comments describe that unit on that bench.
ShownStability on the pad. The customer lies back on the ROM Pad and walks through the setup: no lumbar support, his head dropping back until he scoots up to rest it on the end of the pad. He says the stretch is there but it doesn’t feel safe and he’s wobbling, then describes how much harder it got with 100-pound dumbbells, especially when one side pressed up faster than the other. He shows the movement without weights; these are his words about his own sets on that unit.
ShownHow the foam responds to pressure. The pad compresses where a hand presses into it and springs back on release. That is compliance: the support gives under local pressure. It is not a durability test, and it does not show the pad under a loaded bar.
The useful question for any support is how it behaves when pressure is applied, and whether it holds the setup you need.
Half foam roller and Launch Pad®: construction and setup
Dan Palacios, strength coach (Kinetic Training). Dan is an AMM partner. The half foam roller in these clips is not identified as any particular brand.
ShownDan lies on a half foam roller laid along the bench and unracks a barbell. He then holds up The Launch Pad® and points out its textured flat sections and chamfered edges, and finally sets up and presses on it. The two supports put very different shapes under the torso: a narrow, rounded ridge on one, broad contoured sections on the other.
ClaimedDan explains that the roller sits directly on the spine and that squeezing the shoulder blades back means pressing into its edges, and that the chamfered edges of The Launch Pad® let the shoulder blades move. That is his explanation of the mechanism. The footage does not expose the shoulder blades well enough to show the blade-to-rib-cage relationship that would confirm it, and when he mentions range of motion he is describing the setup, not reporting a measurement.
Dumbbell pressing on the two supports
Dan Palacios, strength coach (Kinetic Training), an AMM partner. One set on The Launch Pad®, then one on the half foam roller, same bench and dumbbells. The gym lighting is dim.
ShownBoth sets are completed, with no structural failure or gross rollover on either support. What changes is the setup: what sits under the torso, how the shoulders rest relative to the support, and how the press looks from the side.
This is a training demonstration. It was not set up to measure range of motion or shoulder-blade movement, and it should not be read as one. For measured results, see Measured performance.
Compare the designs
Each product takes a different approach to what sits between you and the bench. Seeing the approaches side by side makes the design differences easier to follow before getting into specifications.
| Approach | Products | The question to ask |
|---|---|---|
| Contoured support with adjustable lumbar positioning | The Launch Pad® | How do its contact shape, lumbar adjustment and surface affect the setup, and which outcomes have been measured? |
| Conventional flat support | Standard flat bench | Where does the existing pad contact this athlete, and what movement does that setup allow? |
| Wider and thicker flat support | Thompson Fat Pad® | What does the added contact area change about support, positioning and available movement? |
| Localized raised support | AbMat® ROM Pad, TorQ Gear ROM BloQ | What clearance does the support create, how does it fit and behave under load, and what movement results? |
Side by side
| What’s compared | The Launch Pad® | Standard flat bench | Thompson Fat Pad® | AbMat® ROM Pad | TorQ Gear ROM BloQ |
|---|---|---|---|---|---|
| Support geometry | Contoured upper and lower torso sections with a raised lumbar section | A flat pad under the whole torso | A flat pad, wider and thicker than a standard pad | A narrow, raised strip along the spine | A raised support block under the torso |
| Dimensions | 30″ L × 12.5″ W × 3″ H | Varies by model | 50″ L × 14.5″ W × 4.5″ thick | 18″ L × 5.75″ W × 2.875″ H | Not listed |
| Construction | High-density molded polyurethane over an anodized aluminum support plate | Varies by model | Vinyl-covered pad on a plywood basePadding material not listed | Molded foam | Not listed |
| Weight | About 22 lb | Varies by model | 32 lb | Under 2 lb | Not listed |
| Adjustable lumbar support | Yes. Height-adjustable, pin-secured at each setting | None on a typical flat pad | None listed | None listed | None listed |
| Surface and traction | Molded micro-dot texture on the upper and lower torso sections | The bench’s own upholstery | “Grabber” grip vinyl cover | Surface texture not listed | Not listedA separate ROM BloQ Pad is sold for added grip and comfort |
| Attachment to the bench | Two cam straps, no toolsFits most flat, adjustable and machine benches | Built in; nothing to attach | Bolts on in place of the bench padDrilling and extra hardware may be needed on non-Rogue benches | Elastic hook-and-loop strapBenches up to 12″ wide | Used on benches, machines and chest-supported setupsAttachment details not listed |
| Uses listed by the maker | Pressing, pulling, accessory, floor and selected lower-body work, free-weight and machine | Varies by model | Not listed; the page refers to bench pressing | Bench, dumbbell and machine presses and flyesAbMat notes it may not be ideal for maximal-load or competition-style benching | Presses, flys, rows, chest-supported rows, preacher curls and machine work |
| Published product research | 3 peer-reviewed studies of The Launch Pad®, conducted by independent university research teams | Not a single product; the Launch Pad studies used flat-bench conditions as the comparison, identified in each paper | No published studies linkedRogue cites the designer’s seven years of research | None cited | None cited |
DocumentedLaunch Pad details from AMM’s product specifications. Competitor details from Rogue Fitness, AbMat and TorQ Gear product pages, reviewed November 18, 2026.
A wider surface changes support. What does it change about movement?
The Thompson Fat Pad takes the wider-and-thicker approach. Its larger contact area is meant to support more of the upper body, and a wider pad does give more physical support. Whether that extra width contacts, and limits, a given athlete’s shoulder blades depends on their build, how they set up, how much the pad gives, and the movement being performed.
Claims about better shoulder-blade movement or fewer injuries are a different matter. Those are outcomes, and they need measurements of those outcomes. Extra width, customer comfort and a secure setup answer different questions.
A raised strip creates clearance. How does it behave under load?
The ROM Pad and ROM BloQ narrow the support under the spine so the shoulder blades have space on either side. That clearance is a real geometry change you can see. How well the support fits a particular bench, how much it compresses and rebounds, and how the athlete actually moves on it are separate questions, which is why the demonstrations above focus on fit and foam response.
Clearance, joint motion and bar travel are three different things
Comparisons of bench supports often blur three ideas together. Keeping them apart is the simplest way to judge a claim.
Added clearance
The space a support leaves around the shoulder blades. It is a feature of the design, and you can see it in a product photo or a clip.
Joint motion
How far the shoulder joint and shoulder blades actually move during a rep. Measuring it takes motion capture or imaging. None of the products here, The Launch Pad® included, has published measurements of it.
Bar travel
The vertical distance the bar moves, recorded with a position transducer. This is what the acute Launch Pad study measured, and the paper reports it as range of motion.
A design that adds clearance creates the opportunity for more movement. Whether that movement happens, and how much, has to be measured separately.
Examine the claims
Here is what each maker or speaker says, the outcome each statement points to, and the evidence offered for it on the reviewed page. We hold our own product to the same standard.
| Who says it | The claim | Outcome claimed | Evidence offered |
|---|---|---|---|
| Rogue FitnessThompson Fat Pad® | Claimed“Promote Scapular Movement”; uninhibited movement “helps to eliminate AC tears”; the pad will “maximize power and minimize injury” | Shoulder-blade movement, power, injury reduction | No research linked. The page credits the designer with “seven years of research” without citing studies. |
| AbMatROM Pad | Claimed“Increase range of motion and scapular retraction” during pressing | Range of motion, shoulder-blade retraction | None cited. AbMat’s FAQ adds that it may not be ideal for maximal-load or competition-style benching. |
| TorQ GearROM BloQ | ClaimedSays it “allows the shoulder blades to move more naturally”; shows a “2–4″” figure labeled “More Range of Motion” | Shoulder-blade movement, range of motion | None cited. No method is given for the 2–4″ figure. |
| Dan PalaciosCoach, AMM partner | ClaimedA roller’s edges press into the shoulder blades as load increases | A mechanism of restricted shoulder-blade movement | His explanation, shown with setups on camera. The footage does not show the shoulder blades well enough to confirm it. |
| AMMThe Launch Pad® | ClaimedThe contoured sections and adjustable lumbar support leave room for the shoulder blades and hold a repeatable setup | Design rationale for positioning | The published studies did not measure shoulder-blade movement, so this remains design rationale. |
| AMMThe Launch Pad® | MeasuredMore bar travel, greater pec activation, higher bar velocity, larger strength gains | Performance outcomes against flat-bench conditions | Three peer-reviewed studies by independent university research teams. Details below. |
The point of the table is the gap between a physical feature and a biomechanical or clinical outcome. Width, clearance and contour are design features. Better shoulder-blade movement or fewer injuries would need their own measurements.
Measured performance
Three peer-reviewed studies, designed and run by independent university research teams, compared The Launch Pad® with flat-bench conditions in trained men. Each result below names its study, the people tested, the protocol and the comparison. None of these studies tested the Fat Pad, ROM Pad or ROM BloQ, so they are not head-to-head results against those products.
Measured bar travel
44 cm with Launch Pad · 38 cm without
Average vertical bar displacement in a crossover study of 10 trained men performing five repetitions at 70% of one-repetition maximum. The same Rogue Flat Utility Bench 2.0 was tested with and without Launch Pad.
The difference was statistically significant (p = .005). Bar travel is how far the bar moved. Kidwell et al., International Journal of Exercise Science, 2026.
Acute mechanics · Kidwell et al., 2026
One session, two conditions
- 10 resistance-trained men, randomized crossover
- Five reps at 70% 1-RM, same Rogue bench with and without The Launch Pad®
- Mean bar velocity 0.40 → 0.47 m/s (17.5% higher)
- Pec activation up to 27% greater (left 68.3 → 86.8% MVC; right 70.2 → 87.3% MVC)
Four-week strength · Goldman et al., 2025
Twelve supervised sessions
- 42 intermediate-trained men, randomized parallel groups
- Launch Pad group vs conventional flat-bench group
- Average 1-RM gain 18.4 kg vs 11.1 kg (p < .001)
Eight-week football · Blatney et al., 2026
Twenty-four supervised sessions
- 30 collegiate football players, randomized parallel groups
- Launch Pad group vs conventional flat-bench group
- Average 1-RM gain 19.4 kg vs 9.7 kg; NFL-225 reps +7 vs +4; seated medicine-ball throw +2.7 m vs +2.0 m (all p < .001)
All three studies measured performance in trained male lifters. AMM supplied the equipment and had no other role in the research.
Documented product history
The Launch Pad® dates to April 2021, when Advanced Muscle Mechanics was founded to bring it to market, years before the documented introductions of the AbMat ROM Pad and the TorQ ROM BloQ.
The dates below are documented milestones: a company founding, a promotion, an introduction, a store listing or an announced presale. They are not claims about anyone’s first sale.
-
Traditional
Standard flat bench
A long-standing equipment category with no single introduction date. When a study or demonstration uses a flat bench, the specific model is named there.
-
February 6, 2013
Thompson Fat Pad®
Designer Donnie Thompson published his “FatPadPromo” video, which shows the pad was being promoted publicly by that date. The Fat Pad predates The Launch Pad®. Video
-
April 2021
The Launch Pad®
Advanced Muscle Mechanics, LLC was founded in April 2021 to bring The Launch Pad® to market. AMM’s public introduction article, “The Launch Pad comes to life,” followed on July 12, 2021. AMM news archive
-
October 1, 2025
AbMat® ROM Pad
AbMat’s store records the ROM Pad listing as published October 1, 2025, and an archived copy shows it listed for sale by October 9, 2025. AbMat listing · Archived copy
-
June 1, 2026
TorQ Gear ROM BloQ · announced presale
TorQ’s founder announced a June 1 presale on May 5, 2026, and repeated the June 1 drop date on May 27. TorQ has since announced a ROM BloQ V2 for a November 25 drop; that revision is separate from the original product’s introduction. May 5 post · May 27 post
Patents. The Launch Pad® is protected by two issued U.S. patents, 12,115,411 and 12,678,656. An introduction date, a patent filing and a patent grant each establish something different, so they are listed separately from the timeline. Patent information
Which approach fits what you want to change?
If you want to change the surface itself
The Launch Pad®
It replaces the flat contact area with contoured torso sections and a lumbar support you set to your back. Two cam straps fit it to most flat, adjustable and machine benches without tools, so it moves with you between benches, and it is the only product here with peer-reviewed studies published on it.
If you want a thicker, wider flat surface
A fat pad
It replaces your bench pad and is usually bolted on, so it stays with that bench.
If you want a light, portable raised strip
A ROM pad or ROM BloQ
Light and simple, and it narrows the support under your spine. Neither lists a lumbar support.
If you want to shorten the rep instead
A range limiter
To train lockouts or keep the bar off the bottom of the press, a bar-mounted pad or a board press stops the bar above your chest. Those limit range rather than change the bench surface, so they are not compared here. Bench press range of motion, explained covers the difference.
Change the surface you press from.
Every Launch Pad® comes with a 30-day risk-free money-back guarantee.
See The Launch Pad®Sources
- Kidwell JA, Yamamoto T, Hetherton KJ, et al. Acute effects of thoracic-spinal elevation via a novel bench press pad on sEMG and barbell kinetics in resistance-trained males. International Journal of Exercise Science 19(1), 2026. intjexersci.com/files/ijes/vol19/iss1/3.pdf
- Goldman P, Taylor J, Yamamoto T, et al. Scientific Journal of Sport and Performance 4(4), 2025. doi.org/10.55860/JCDL3612
- Blatney AE, Kidwell JA, Yamamoto T, Goldman P, Hetherton KJ, Dolezal BA. Scientific Journal of Sport and Performance 5(1), 2026. doi.org/10.55860/RNUB8627
- Rogue Fitness. Thompson Fat Pad™ product page. Reviewed November 18, 2026. roguefitness.com/thompson-fatpad
- AbMat. ROM Pad product page. Reviewed November 18, 2026. abmat.com/products/rom-pad
- TorQ Gear. Chest/Back ROM BloQ product page and home page. Reviewed November 18, 2026. torq-gear.com/products/bloq
- Donnie Thompson. “FatPadPromo,” YouTube, February 6, 2013. youtube.com/watch?v=f8GeB9bmSgo
- Advanced Muscle Mechanics. “The Launch Pad comes to life,” July 12, 2021. advancedmusclemechanics.com/blogs/news